Dc Gear Motor can be defined as an extension of Dc Motor which already had its Insight details demystified here. A dc Gear Motor has a gear assembly attached to the motor. The speed of motor is counted in terms of rotations of the shaft per minute and is termed as RPM .The gear assembly helps in increasing the torque and reducing the speed. Using the correct combination of gears in a dc gear motor, its speed can be reduced to any desirable figure. This concept where gears reduce the speed of the vehicle but increase its torque is known as gear reduction.
Application field: usually used Electronic door locks, shutter motor, home audio equipment, sweep the floor machine robot
Features: dc gear motor drive precision, small volume, large torque, low noise, durability, low energy consumption, customized power design,easy installation, easy maintenance;Simplify design and save space.
Method of use: the best stable in horizontal plane, installed on the dc gear motor output shaft parts, cannot use a hammer to knock,knock prone to press into the dc gear motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
Dc geared motors should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a geared motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
Dc geared motors should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
Dc Gear Motor Dc Gear Motor,Gear Box Motor,Gear Reduction Motor,Small Diameter Dc Gear Motor Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com
Among them, the fourth quarter revenue of 6.799 billion euros, unchanged from the same period last year; net profit of 412 million euros, a loss of 420 million euros in the same period last year. Medical insurance business sales of 2.83 billion euros, adjusted post-earnings and amortization profit (EBITA) of 541 million euros; consumer life business sales of 1.43 billion euros, EBITA of 187 million euros; lighting business sales of 2.3 billion euros, EBITA It is 218 million euros.
According to the financial report, the sales of Philips LED business accounted for about 30%. From the LED products of Philips and the promotion of the company, the LED share of the entire lighting market should be at 25% or lower. This is determined by the market's acceptance of new light sources, and the traditional lighting companies are not fully transformed. of. 
(2013 quarterly sales of LED business)
Philips said that the group's 2013 performance growth has two reasons. First, in 2012, it was caused by the company's monopoly on the monopoly of the company, causing losses; second, the reduction of restructuring costs. Although the group has reached its 2013 growth target, it is still cautious about the future global economic situation. It is expected that sales will increase by 4%-6% in 2014, and profit growth in 2016 will reach 11%-12%. 
Royal Dutch Philips Group (Philips) released its annual financial report on January 28, saying its 2013 sales were 23.329 billion euros, down 1% from 234.57 in 2012; but net profit reached 1.172 billion euros, reversing the loss of 30 million in 2012. The situation of the euro.